News

  • [Copy]  Dynamic balancing of centrifugal pump impeller

    [Copy] Dynamic balancing of centrifugal pump impeller

    The impeller is the main rotating component which normally has vanes to impart and direct the centrifugal force to the liquid. Usually, slurry pump impellers have a plain or a Francis type vane. Vibration caused by mass imbalance in...
    Read more
  • Good News! 8x6E-MAH Spare Parts with Ceramic Material Provided to our Malaysia Customer!

    Good News! 8x6E-MAH Spare Parts with Ceramic Material Provided to our Malaysia Customer!

    Good News! 8x6E-MAH Spare Parts with Ceramic Material Provided to our Malaysia Customer! MAH Heavy duty horizontal slurry pumps. High efficiency transfer of abrasive and high density slurries with extended wear life and reliable service intervals. About the wet ends parts material, except A05 and...
    Read more
  • Notice: Six Preparations To Be Done Before The Pump Starts

    Notice: Six Preparations To Be Done Before The Pump Starts

          1. Irrigation pump (except for the submerged pump, before the other pumps are started (the first time the self-priming pump is started), the pump should be pumped (that is, the pumping medium must be filled with the pump chamber))  2. Irrigation device: Open the shut-off val...
    Read more
  • Mechanical Seal Maintenance Program Under Special Working Conditions

    Mechanical Seal Maintenance Program Under Special Working Conditions

    In the pumping device, the mechanical seal of the mobile device accounts for about 80%-85% of the total number of dynamic seals. In the case of a pump failure, the mechanical seal failure accounts for about half of the total maintenance work. It can be seen that the mechanical seal occupies the p...
    Read more
  • GOOD NEWS! HYDRAULIC SLURRY PUMP FINISHED AND EXPORTED TO KOREA

    GOOD NEWS! HYDRAULIC SLURRY PUMP FINISHED AND EXPORTED TO KOREA

    GOOD NEWS! HYDRAULIC SLURRY PUMP FINISHED AND EXPORTED TO KOREA   Slurry is a mixture of liquid and particles of solid matter, some of them incapable of being dissolved. This mixture could be pumped, which is the procedure often used as a convenient way of handling soli...
    Read more
  • Good News! 100 sets Water Fire Pumps Finished and Exported to Vietnam

    Good News! 100 sets Water Fire Pumps Finished and Exported to Vietnam

    End Suction and Split Case Pump total of 100 sets for the fighting system is finished! Pump details as following: ISA50/26: flow rate 65m3/h@91m; ISA65/26: flow rate 120m3/h@90m; ISA80/26: flow rate 190m3/h@83m; ISA100/26: flow rate 295m3/h@85m; ISA150/50...
    Read more
  • What are the advantages and disadvantages of high voltage motors compared to low voltage motors?

    What are the advantages and disadvantages of high voltage motors compared to low voltage motors?

    What are the advantages and disadvantages of high voltage motors compared to low voltage motors? For AC motors, high voltage motors with rated voltages of 1000V and above; low voltage motors of less than 1000V (the limit in some materials is 1140V). For DC motors, high voltage motors with rated ...
    Read more
  • Good News! ISO100x65-250 End Suction Centrifugal Water Pumps Finished and Exported to United States

    Good News! ISO100x65-250 End Suction Centrifugal Water Pumps Finished and Exported to United States

    Good News! ISO100x65-250 End Suction Centrifugal Water Pumps Finished and Exported to United States The ISO range has been designed to international standard ISO 2858/5199 ensuring a sturdy & reliable, long lasting, high performing product. Suitable Appli...
    Read more
  • Important Factors When Selecting Chemical Pumps

    Important Factors When Selecting Chemical Pumps

    Following are the important factors taken in to consideration while selection chemical pumps : 1. Capacity and discharge head This expected in usual terms Suction process pump may be required to lift the liquid from a lower level or liquid coming under pressure at the su...
    Read more
  • How to caculate a deep well pump head?

    How to caculate a deep well pump head?

    How to caculate a deep well pump head? A suitable pump is selected suitably based on not only capacity but also head. So what is the pump head? This is the vertical distance that you are able to pump the liquid. Say your pump is rated for a maximum head of 100 feet, this...
    Read more
  • GOOD NEWS! SEWAGE WATER PUMP FINISHED AND EXPORTED TO VIETNAM

    GOOD NEWS! SEWAGE WATER PUMP FINISHED AND EXPORTED TO VIETNAM

    GOOD NEWS! SEWAGE WATER PUMP FINISHED AND EXPORTED TO VIETNAM WQ Series submersible sewage pump is mainly used for municipal works, industrial bulidings, hotels, hospitals, civil air defence, mines etc. Trades to drain off the sewage, waste water, rainwater and living w...
    Read more
  • Good News!  Double Suction Pumps Finished and Exported to Vietnam for Fire Fighting System

    Good News! Double Suction Pumps Finished and Exported to Vietnam for Fire Fighting System

    Good News! Double Suction Pumps Finished and Exported to Vietnam for Fire Fight System! centrifugal split case pump has the high head, large flow characteristics, widely used in engineering. It is late-model energy-saving horizontally split pump newly developed...
    Read more
  • Good News!  Multistage Pump Finished and Exported to Malaysia for Desalination

    Good News! Multistage Pump Finished and Exported to Malaysia for Desalination

    Good News! D280-43x6 Horizontal Multistage Pumps Finished and Exported to Malaysia for Desalination! D Centrifugal Horizontal Multistage Pump is high-efficiency, energy-saving , and have long life and installing & repairing is very convenient. It can delive...
    Read more
  • Top 4 causes of vibration of centrifugal pumps

    Top 4 causes of vibration of centrifugal pumps

    Top 4 causes of vibration of centrifugal pumps 1. Shaft A pump with a long shaft is prone to insufficient shaft stiffness, too large deflection, and poor straightness of the shaft system, causing friction between the moving member (drive shaft) and the static member (sliding bearing or ring) to...
    Read more
  • The structure and type of metering pump

    The structure and type of metering pump

    The structure and type of metering pump The metering pump is composed of three parts: the transmission base part, the pump head part and the motor. The structure mainly includes a driving end and a hydraulic end. According to the different hydraulic end, it can be divided into: plunger type, ...
    Read more
  • What is the difference between Soft Seal Butterfly Valve & Hard Seal Butterfly Valve?

    What is the difference between Soft Seal Butterfly Valve & Hard Seal Butterfly Valve?

    Hard Sealing Butterfly Valve Butterfly valve hard seal means that both sides of the seal pair are made of metal material or other hard materials. This seal has poor sealing performance, but is resistant to high temperatures, abrasion and mechanical properties. Such as: steel + steel; steel + cop...
    Read more
  • Different Grey Cast Iron Brands Comparision

    Different Grey Cast Iron Brands Comparision

     As we all known there’s different brand standards of grey cast iron material. In order to for your easy compare, MIMO provide a format as below:   * Above is listed some brands for reference, if any query welcome to contact MIMO.
    Read more
  • What Should We Do During Pump Operation?

    What Should We Do During Pump Operation?

    What Should We Do During Pump Operation? 1. Stuffing Box Make sure that the stuffing box has been properly packed (see sub-section) and above all that the gland has not been tightened too firmly as, otherwise, damage will occur to the packing and the shaft sleeve. See to it that it is not tighte...
    Read more
  • Good News!  End Suction Pump Finished and Exported to Colombia for Sample.

    Good News! End Suction Pump Finished and Exported to Colombia for Sample.

    Good News! IS65-50-160 End Suction Pump Finished and Exported to Colombia for Sample! IS Series single stage end suction centrifugal pump is an energy-saving pump designd by teamwork in the whole nation, it is improved on a basis on model BA, A and other single stage wat...
    Read more
  • Ten Tips About Pump Maintenance

    Ten Tips About Pump Maintenance

    Ten Tips About Pump Maintenance Even smooth running of the pump rotor is essential When delivering from a tank the liquid level must always be well above inlet opening The performance as indicated on the driver nameplate must not be exceeded The stuffing box must always drip slightly to remove...
    Read more
  • Designing a floating pump station to solve long-standing challenges

    Designing a floating pump station to solve long-standing challenges

      Designing a floating pump station to solve long-standing challenges By Siobhan Day, Journalist, Pump Industry Magazine Faced with the challenge of low water levels, a shared recreational area and the need for easy maintenance, Federation Council in New South Wales had its work cut out for ...
    Read more
  • ISO STANDARD END SUCTION PUMP FITTED WITH OIL LUBRICATED BEARINGS

    ISO STANDARD END SUCTION PUMP FITTED WITH OIL LUBRICATED BEARINGS

    Pump Lubrication 1. PUMPS FITTED WITH OIL LUBRICATED BEARINGS 1.1 Oil Specification HOUSING  MODULE OIL LUBE OIL SPECIFICATION QTY(ml) Preferred oJSs are those that have non foaming properties. Typicatfy, twbsne of hyctfauiic osts wotitct be stiitable. Viscosity of SAE20 to SAE30 (ISO V...
    Read more
  • Gland Assembly 044 for MAH Horizontal Slurry Pump

    Gland Assembly 044 for MAH Horizontal Slurry Pump

    Gland assembly is used for seal the gland packing . It helps to make a good sealing for the pump. Throat bush is a very important sealing part of MAH Horizontal Slurry Pump. Code is 044. Standard material is cast iron.   Material For different medium and PH value, various materials can be used ...
    Read more
  • Centrifugal pump impeller, do you know these 5 repair methods?

    Centrifugal pump impeller, do you know these 5 repair methods?

    Centrifugal pump impeller, do you know these 5 repair methods? The centrifugal pump will wear and corrode gradually due to the sediment, the erosion of the water flow and the corrosion of the medium. The surface of the blade often forms grooves or streaks, or is damaged by cavitation, and the le...
    Read more
  • Ten words to solve equipment oil spill

    Ten words to solve equipment oil spill

    Ten words to solve equipment oil spill. First, equipment oil leakage is generally divided into three types: oil leakage, oil drop, and oil flow: (1) Oil leakage. For a fixed connection, a drop of oil every half hour is oil leakage. For the part where the activity is connected, one drop of oil e...
    Read more
  • Pump cavitation and suction stroke relations

    Pump cavitation and suction stroke relations

    Pump users generally require a pump suction (high vertical difference from the suction level to the center of the pump inlet), but there is no term for suction in domestic pump standards and specifications. The term associated with it is the cavitation margin, which is approximately equal to 10 ...
    Read more
  • What is the best solution for cable water intake?

    What is the best solution for cable water intake?

    Cable water intake is also a very common power cable failure. How do you solve the problem when the cable enters the water? It is a cumbersome thing to have water in the cable. So far, there is no particularly effective way to solve it, either to make a middle joint or to change the cable. In vi...
    Read more
  • Good News!  End Suction Pumps are Finished and Exported to Australia!

    Good News! End Suction Pumps are Finished and Exported to Australia!

    Good News! ISA40/16 End Suction Pumps are Finished and Exported to Australia! ISA Series end suction centrifugal pumps are designed complying to BS EN733/DIN24255 standard. This series of pumps have great advantages in interchangeable parts, high quality and low cost, wide applications in plants,...
    Read more
  • Global Analysis of the Pump Market in the Oil & Gas Industry

    Global Analysis of the Pump Market in the Oil & Gas Industry

    Global Analysis of the Pump Market in the Oil & Gas Industry The global pump market in oil and gas stood at a staggering $9 billion market in 2014. Although the growth rate for pumps is expected to be low during the current year because of the recent weakness in investments in oil and gas, th...
    Read more
  • Good News!  Double Suction Pumps are Finished and Exported to Bahrain!

    Good News! Double Suction Pumps are Finished and Exported to Bahrain!

    Good News! 350S-26 Double Suction Pumps are Finished and Exported to Bahrain! S centrifugal split case pump has the high head, large flow characteristics, widely used in engineering. It is late-model energy-saving horizontally split pump newly developed by us on the base of the old style double s...
    Read more
  • Good News! Piston Pump Exported to Our  Venezuela Friend!

    Good News! Piston Pump Exported to Our Venezuela Friend!

    Good News! Piston Pump Exported to Our  Venezuela Friend! YE series pump are high pressure horizontal water pump to handle big head request field. Here please note the pump details as following: YE1 Capacity: 10Gallon/min Pressure: 10 Mpa Plunger stroke: 60mm Plunger Dia. : 24mm Pump Speed: 500rp...
    Read more
  • 132KW Submersible Slurry Pump Exported to Our Malaysia Friend!

    132KW Submersible Slurry Pump Exported to Our Malaysia Friend!

    Submersible Slurry Pump Exported to Our Malaysia Friend! SS series are a heavy duty, electro-submersible slurry pumps designed to handle a wide range of slurries and abraisive particles in submersible applications in mining and indus...
    Read more
  • 6×4 MAH Slurry Pump Exported to Our Malaysia Friend!

    6×4 MAH Slurry Pump Exported to Our Malaysia Friend!

    6x4 MAH Slurry Pump Exported to Our Malaysia Friend! MAH Heavy duty horizontal slurry pumps. High efficiency transfer of abrasive and high density slurries with extended wear life and reliable service intervals.   Recently we exported 3 sets 6x4AH to our Malaysia client ...
    Read more
  • 30sets WQ Submersible Sewage Pump Exported to Our America Friend!

    30sets WQ Submersible Sewage Pump Exported to Our America Friend!

    30 sets WQ Submersible Sewage Pump Exported to Our America Friend!  MIMO WQ Series submersible sewage pump is mainly used for municipal works, industrial buildings ,hotels, hospitals, civil air defense, mines etc. Trades to drain off the sewage, waste water, r...
    Read more
  • 8X6 MAH Slurry Pump Exported to Our Malaysia Friend!

    8X6 MAH Slurry Pump Exported to Our Malaysia Friend!

    8X6 MAH Slurry Pump Exported to Our Malaysia Friend! MAH Heavy duty horizontal slurry pumps. High efficiency transfer of abrasive and high density slurries with extended wear life and reliable service intervals. Ceramics pump have good performance in wear-resis...
    Read more
  • Good News! MAHR Slurry Pump Exported to Our Zambia  Friend!

    Good News! MAHR Slurry Pump Exported to Our Zambia Friend!

    Good News! Submersible Slurry Pump Exported to Our Zambia Friend! MAHR Heavy duty horizontal slurry pumps. High efficiency transfer of abrasive and high density slurries with extended wear life and reliable service intervals. Recently we exported 6 sets 6x4E-MAHR to our Zambia client for mining a...
    Read more
123 Next > >> Page 1 / 3

WhatsApp Online Chat !